Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY19 is not expected to be complete until June, 2020.

  1. Dual Plane 3D Compton Scattering Imager with Pixelated CZT Detectors for 1-10MeV Gamma Ray

    SBC: H3D            Topic: None

    Phase I has proven that the current setup achieves better than 8mm spatial resolution for 2.2MeV prompt gammas. However, 1mm spatial resolution presents a significant challenge for the current setup due in part to limited timing resolution and count rate. A new analog ASIC will be developed to replace the current analog ASIC that will have better timing resolution and deliver higher count rates. I ...

    SBIR Phase II 2019 Department of CommerceNational Institute of Standards and Technology
  2. Advanced Instrumentation for Non-Nulling Stack Velocity Testing

    SBC: AIRFLOW SCIENCES CORPORATION            Topic: None

    Industrial facilities, manufacturing plants, and electric power plants that burn fossil fuels exhaust the combustion products to atmosphere through their smokestacks. Stack pollutant emissions are quantified using manual testing methods developed in the 1960s, which are prone to error if non-axial flow exists in a stack.Recently, NIST has been working on an improved technique of performing 3D flow ...

    SBIR Phase I 2019 Department of CommerceNational Institute of Standards and Technology
  3. Development of a Neutron-based Nondestructive Test Method for Concrete Petrography and Chemical Analysis

    SBC: TOURNEY CONSULTING GROUP, LLC            Topic: None

    To evaluate the technical feasibility of prompt gamma neutron activation (PGAA) as an alternative to a set of standard destructive tests of concrete petrography including aggregate type, water/cement ratio, aggregate/binder ratio, density, chloride content and chloride bulk diffusion constant; and to determine the specifications for the design of a dedicated commercial laboratory-based PGAA facili ...

    SBIR Phase I 2019 Department of CommerceNational Institute of Standards and Technology
  4. Combined Extinction/Fluorescence Absorption Diagnostics for Sprays

    SBC: En'urga Inc.            Topic: 9030163R

    This Phase II project will continue the prototype development of a pharmaceutical spray quality audit system. The spray quality audit system will estimate the planar mass distribution, mass flux, and drop size of pharmaceutical sprays that are used in functional coating applications and inhalers. A prototype tomography system will be designed and fabricated and evaluated using various fluorophore.

    SBIR Phase II 2015 Department of CommerceNational Institute of Standards and Technology
  5. Large-Area, High-Uniformity Photodiodes for Infrared Trap Detectors

    SBC: Amethyst Research Incorporated            Topic: 9020168R

    methyst Research Inc. will design, fabricate and test a high uniformity, large area, low noise infrared trap-detector detector for the 1- 4.5 μm wavelength range. This state of the art detector will have a large area (e.g., 1-1.8 cm diameter active area) with a spatial variability of internal quantum efficiency of less than 0.1 % between 1 μm and 4.5 μm. In addition, the internal quantum effici ...

    SBIR Phase I 2015 Department of CommerceNational Institute of Standards and Technology
  6. An Integrated Decision Support Framework for Sustainability CAE

    SBC: BIMCON Inc.            Topic: 9050273R

    The objective of this proposal is to establish the feasibility of developing an integrated decision support framework that transforms the current time-consuming and reactive (post completion of final design) sustainability assessment into a proactive CAE approach that enables the ability to revise designs based on performance against selected sustainability targets in the product design process, i ...

    SBIR Phase I 2011 Department of CommerceNational Institute of Standards and Technology
  7. Decision Support Tools for Sustainable Manufacturing

    SBC: BIMCON Inc.            Topic: 907012R

    Our vision is that of an integrated decision support solution that transforms the current time-consuming and reactive (post-design) sustainability assessment of a product into a proactive approach available in the early design phases. This solution called Sustainability Integrated into Early Design (SIED) will deliver lifecycle sustainability data into early design processes and focus primarily on ...

    SBIR Phase II 2011 Department of CommerceNational Institute of Standards and Technology
  8. Decision Support Tools for Sustainable Manufacturing

    SBC: BIMCON Inc.            Topic: N/A

    The objective of this proposal is to establish the feasibility of developing an integrated decision support tool that transforms the current time-consuming and reactive (post-design) sustainability assessment into a real-time, proactive approach available in the early phases of product design. This tool, called Sustainability Integrated into Early Design (SIED), will define and capture lifecycle-w ...

    SBIR Phase I 2010 Department of CommerceNational Institute of Standards and Technology
US Flag An Official Website of the United States Government