Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY19 is not expected to be complete until June, 2020.

  1. Dual Plane 3D Compton Scattering Imager with Pixelated CZT Detectors for 1-10MeV Gamma Ray

    SBC: H3D            Topic: None

    Phase I has proven that the current setup achieves better than 8mm spatial resolution for 2.2MeV prompt gammas. However, 1mm spatial resolution presents a significant challenge for the current setup due in part to limited timing resolution and count rate. A new analog ASIC will be developed to replace the current analog ASIC that will have better timing resolution and deliver higher count rates. I ...

    SBIR Phase II 2019 Department of CommerceNational Institute of Standards and Technology
  2. Advanced Instrumentation for Non-Nulling Stack Velocity Testing

    SBC: AIRFLOW SCIENCES CORPORATION            Topic: None

    Industrial facilities, manufacturing plants, and electric power plants that burn fossil fuels exhaust the combustion products to atmosphere through their smokestacks. Stack pollutant emissions are quantified using manual testing methods developed in the 1960s, which are prone to error if non-axial flow exists in a stack.Recently, NIST has been working on an improved technique of performing 3D flow ...

    SBIR Phase I 2019 Department of CommerceNational Institute of Standards and Technology
  3. Development of a Neutron-based Nondestructive Test Method for Concrete Petrography and Chemical Analysis

    SBC: TOURNEY CONSULTING GROUP, LLC            Topic: None

    To evaluate the technical feasibility of prompt gamma neutron activation (PGAA) as an alternative to a set of standard destructive tests of concrete petrography including aggregate type, water/cement ratio, aggregate/binder ratio, density, chloride content and chloride bulk diffusion constant; and to determine the specifications for the design of a dedicated commercial laboratory-based PGAA facili ...

    SBIR Phase I 2019 Department of CommerceNational Institute of Standards and Technology
  4. Nanomachine Device for Semiconductor Process Control Monitoring

    SBC: Xallent LLC            Topic: None

    Conventional characterization and test methods are increasingly ineffective when applied to structures less than 100 nanometers, causing challenges across R&D, process control and failure analysis. An increasing number of subtle defects become prominent drivers of failure as device size and operating margins decrease, e.g., processing anomalies in thin gate oxides, substrate problems related to do ...

    SBIR Phase I 2019 Department of CommerceNational Institute of Standards and Technology
  5. A Tool for Building Semantically Interoperable Specification and Standards

    SBC: XSB INC.            Topic: 9010273R

    Standards and specifications are widely used in government and industry to define requirements for products and processes and insure interoperability, safety, and quality of industrial and domestic products. Specifications and standards documents almost always cross-reference other standards and specification. Taken together, the web of interdependent standards forms an immensely important knowled ...

    SBIR Phase I 2015 Department of CommerceNational Institute of Standards and Technology
  6. Large-Area, High-Uniformity Photodiodes for Infrared Trap Detectors

    SBC: AMETHYST RESEARCH INCORPORATED            Topic: 9020168R

    methyst Research Inc. will design, fabricate and test a high uniformity, large area, low noise infrared trap-detector detector for the 1- 4.5 μm wavelength range. This state of the art detector will have a large area (e.g., 1-1.8 cm diameter active area) with a spatial variability of internal quantum efficiency of less than 0.1 % between 1 μm and 4.5 μm. In addition, the internal quantum effici ...

    SBIR Phase I 2015 Department of CommerceNational Institute of Standards and Technology
  7. Decision Support Tools for Sustainable Manufacturing

    SBC: BIMCON Inc.            Topic: N/A

    The objective of this proposal is to establish the feasibility of developing an integrated decision support tool that transforms the current time-consuming and reactive (post-design) sustainability assessment into a real-time, proactive approach available in the early phases of product design. This tool, called Sustainability Integrated into Early Design (SIED), will define and capture lifecycle-w ...

    SBIR Phase I 2010 Department of CommerceNational Institute of Standards and Technology
  8. Distributed MBARK Based Mobile Face Recognition

    SBC: Ad Harmony            Topic: N/A

    Perform a feasibility study on developing a face recognition application in a cloud computing environment utilizing MBARK as the middleware. The application will have a client piece that will run on a mobile device and a server piece that will run on a higher-performance computing cluster. The specific objectives of the feasibility can be enumerated as follows: 1. Split/distribute the MBARK middle ...

    SBIR Phase I 2010 Department of CommerceNational Institute of Standards and Technology
US Flag An Official Website of the United States Government