For best search results, use the search terms first and then apply the filters

The Award database is continually updated throughout the year. As a result, data for FY19 is not expected to be complete until April, 2020.

  1. Aided recovery from Visual Loss

    SBC: AMS. Inc.            Topic: N/A


    SBIR Phase I 1994 Department of DefenseArmy
  2. Toughened E-Beam Curable Resins for Low Cost, Rapidly Pultruded, Filament Wound and Resin Transfer Molded Composites


    The objective of the proposed program is to demonstrate the feasibility of an innovative, cost-effective, rapid-pultrusion composite processing technique and newly formulated resins which substantially reduce the need for expensive tooling, high puller tensions (dies are expected to be an order of magnitude shorter than conventional pultrusion dies) and slow thermal processing and can cure the com ...

    SBIR Phase II 1996 Department of DefenseArmy
  3. Human performance issues in automatic target recognition and situation awareness displays

    SBC: ALPHATECH, INC.            Topic: N/A


    SBIR Phase I 1994 Department of DefenseArmy
  4. Self-Organizing Biomolecular Materials as Structural and Patterning Elements for Device Fabrication

    SBC: AMBERGEN, INC            Topic: N/A

    The engineering of materials on a nanometer scale is an important technological goal which would facilitate the development of a new generation of materials and devices. A variety of biological membranes exhibit self-assembly into 2-D arrays including the purple membrane from Halobacteria salinarium and the S-layer from Sulfolobus acidocaldarius. Methods have been developed to use these membrane ...

    SBIR Phase II 1996 Department of DefenseArmy
  5. Extremely Lightweight Hydrogen Fuel Cells

    SBC: ANALYTIC POWER LLC            Topic: N/A

    The fuel cell power supplies of today are two times too heavy compared to man-portable power supplies. A major portion of the weight is in the fuel cell stack, a stack of carbon electrodes with metal bipolar plate separators that are sandwiched between two end plates and held in place by tie rods. We continue to investigate lighter weight materials to use in our conventional fuel cell stack. Ho ...

    SBIR Phase II 1996 Department of DefenseArmy
  6. Using the Image Understanding Architecture and Knowledge Based Reasoning to Recognized Vehicle Types from Multisensor Data



    SBIR Phase I 1994 Department of DefenseArmy
  7. The Detection and Location of Buried Metallic and Nonmetallic Targets

    SBC: Anro Engineering, Inc.            Topic: N/A

    ANRO is currently under a Phase II SBIR contract to evaluate an Ultra-Wideband (UWB) linear radar array and the processing of co- and cross-polarization returns for detecting and discriminating buried mines. Experiments indicate that both metallic and plastic ines located several inches below the suface are reliably detected using a novel real-time cancellation scheme; however, it appears that ta ...

    SBIR Phase I 1996 Department of DefenseArmy
  8. Non-Eroding Fin Materials

    SBC: Applied Research Associates, Inc.            Topic: N/A

    This project will analyze and select promising materials and designs to be used in the plumes of tactical solid rocket motors for missile steering and control. The emphasis is on high-performance refractory materials and compatibility of material systems. The control fins experience severe thermal and severe particulate erosion environments. Missile controllability requires fins with minimal er ...

    SBIR Phase I 1996 Department of DefenseArmy
  9. Next Generation Fire Protective Textiles Incorporating Microencapsulated Flame Retardants

    SBC: Aspen Systems, Inc.            Topic: N/A

    An important facet to a soldier's survivability depends on the clothing worn during combat and training exercises. Common fibers used in the textile industry, particularly nylons and polyesters, are flammable, produce toxic smoke and are potentially hazardous when worn soldiers. Flame retardant materials applied directly to these fibers may adversely alter the properties of the fabric and/or deg ...

    SBIR Phase II 1996 Department of DefenseArmy
  10. Agiel laser and ballistic impact resistant high performance polycarbonate polymers for transparent eye and sensors safety shields

    SBC: Aspen Systems, Inc.            Topic: N/A

    Aspen Systems proposes to design and synthesize transparent polymers with nonlinear, laser absorbing species and subanosecond response times. We will build polydiacetylens and multiphoton, laser-radiation-absorbing species directly into the polymer. Additional multi-photon absorbing chemical species. e.g., derivatives of 1,6 - diphenyl - 1,3,5-hexatriene will be incorporated into the polymer. Stru ...

    SBIR Phase I 1994 Department of DefenseArmy

Agency Micro-sites

SBA logo
Department of Agriculture logo
Department of Commerce logo
Department of Defense logo
Department of Education logo
Department of Energy logo
Department of Health and Human Services logo
Department of Homeland Security logo
Department of Transportation logo
Environmental Protection Agency logo
National Aeronautics and Space Administration logo
National Science Foundation logo
US Flag An Official Website of the United States Government