Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY19 is not expected to be complete until September, 2020.

  1. Innovative C3I Technologies CFOR and AOC Applications for Synthetic Battlefield Development Environment

    SBC: Frontier Technology Inc.            Topic: N/A

    N/A

    SBIR Phase I 1996 Department of DefenseAir Force
  2. Ultra High Heat Flux Electronics Cooler

    SBC: MAKEL ENGINEERING, INC.            Topic: N/A

    N/A

    SBIR Phase I 1996 Department of DefenseAir Force
  3. Economical and Reliable Adaptive Disturbance Cancellation for Lightly Damped Systems

    SBC: PLANNING SYSTEMS, INC.            Topic: N/A

    Efforts to apply active noise and vibration control commercially, while intensifying, continue to be hampered by the cost of the computers required to implement the active algorithms. Currently, the cost of wide-band control is prohibitive for lightly damped systems such as precision structures or highly reverberant acoustic spaces, even if the system has just one canceling actuator and one error ...

    SBIR Phase I 1997 Department of DefenseAir Force
  4. Infrared Fisheye Optics

    SBC: OPTICS 1, INC.            Topic: N/A

    In this Phase I SBIR we will design a series of ultra-wide angle fisheye lenses suitable for fuzing sensors and their related test equipment. The lenses will be customized to cover three spectral bands from 3 microns to 12 microns as well as the visible. There are many factors that will need to be taken into account including control of radial magnification or distortion over the wide 180 degree ...

    SBIR Phase I 1997 Department of DefenseAir Force
  5. Nonintrusive System for Extraction of Interlayer Printed Circuit Patterns

    SBC: Aracor            Topic: N/A

    The goal of this two-phase program is to develop a prototype system which addresses the problem of nondestructively extracting layout patterns for multilayer printed circuit boards. The system will use x-ray digital tomosynthesis for image acquisition, and advanced image processing, including morphological operators, to extract circuit features from the images. The objectives of Phase I are to 1 ...

    SBIR Phase I 1997 Department of DefenseAir Force
  6. Real-Time Inertial Measurement Unit Simulator

    SBC: AMERICAN GNC CORPORATION            Topic: N/A

    This SBIR Phase I project proposes the development of a real-time IMU simulator which can inject simulated electronic signals into the GPS guidance receiver with least intrusion and is applicable to a wide range of navigation systems. The proposed IMU Simulator consists of a PC compatible microcomputer, a set of plug -in IMU signal generator boards, and a set of general purpose flight simulator i ...

    SBIR Phase I 1997 Department of DefenseAir Force
  7. Clay-Templated Nanoporous Graphite Carbon Electrodes for Secondary Batteries

    SBC: Cape Cod Research            Topic: N/A

    We propose to develop a novel type of graphite with high nanoscale porosity by pyrolysis of the precursor embedded in layered clays, with the possiblity of varying the pore size and pore density. In Phase I, we will conduct a feasibility study of the process combined with a molecular modeling effort to predict the diffusion rate of lithium into the material as a function of its porosity. first, ...

    SBIR Phase I 1997 Department of DefenseAir Force
  8. Advance Low-k Dielectrics by the Sol-Gel Process

    SBC: Chemat Technology, Inc.            Topic: N/A

    In this proposal, we plan to synthesize UV-curable, fluorinated polycarbosilane (PCS) using fluoronation and substitution reactions. Conventional polycarbosilane (PCS) has been proven to be a good replacement for spin-on glass (SOG). PCS can be converted to a highly porous silicon oxide/oxycarbide composite at relatively low process temperature by controlling heat treatment temperatu ...

    SBIR Phase I 1996 Department of DefenseAir Force
  9. Multi-Particle Impact Damping Design Methodology for Extreme Environments

    SBC: CSA Engineering, Inc.            Topic: N/A

    CSA Engineering, Inc., and its team partner, Pratt and Whitney, propose to develop and validate a design methodology for using Multi-Particle Impact Damping (MPID) in high temperature applications. Research work has indicated that multi-particle impact dampimg (also referred to as "particle damping") could be a viable option for extreme temperature applications. However, to date, the lack of a r ...

    SBIR Phase I 1997 Department of DefenseAir Force
  10. Compact Visible/UV Laser With Electro-Optic Control

    SBC: Deacon Research            Topic: N/A

    N/A

    SBIR Phase I 1996 Department of DefenseAir Force
US Flag An Official Website of the United States Government