Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY19 is not expected to be complete until September, 2020.

  1. Advanced Tooling Manufacturing for Composite Structures (ATMCS)

    SBC: Fem Engineering            Topic: N/A

    N/A

    SBIR Phase I 1996 Department of DefenseOffice of the Secretary of Defense
  2. Advanced, Man-Portable Locator of Magnetic Targets

    SBC: Quantum Magnetics, Inc.            Topic: N/A

    This SBIR proposal addresses a high priority DoD need for an improved man-portable magnetic sensor to detect and localize mines and UneXploded Ordnance (UXO). UXO field testing has clearly shown the superiority of magnetic-based technology over other technologies such as ground penetrating radar and infrared sensors. Total field magnetometers and gradiometers, although relatively unaffected b ...

    SBIR Phase I 1996 Department of DefenseOffice of the Secretary of Defense
  3. AN YTTRIUM ALUMINUM PEROVSKITE BASED GAMMA-RAY DOSIMETER

    SBC: W Peter Trower Inc.            Topic: N/A

    N/A

    SBIR Phase I 1994 Nuclear Regulatory Commission
  4. Analysis and Improvement of Trivalent Chromium Conversion Coatings for Aluminum Alloys

    SBC: American Research Corporation of Virginia            Topic: N/A

    N/A

    SBIR Phase I 1996 Department of DefenseOffice of the Secretary of Defense
  5. Commercialization of C4I Simulation Components for Disaster Planning and Recovery Using HLA

    SBC: Mystech Assoc., Inc.            Topic: N/A

    Federal, state, local, and military missions for Disaster Relief, Emergency Action, and Humanitarian Assistance (DREAHA) require all of the traditional command, control, communications, computer and intelligence (C4I) functions used by military units for traditional warfare. New civilian systems that leverage and reuse military C4I systems to plan, prepare, identify, vector, monitor, and recover ...

    SBIR Phase I 1997 Department of DefenseOffice of the Secretary of Defense
  6. Compact, High Capacity Parallel Optical Memories

    SBC: Accuwave Corp.            Topic: N/A

    In this proposed SBIR program, Accuwave will investigate and demonstrate architectures for compact hologrpahic storage using materials and system innovations to reduce complexity and improve performance. Crosstalk, data formatting, input/output interfaces, and other relevant parameters will be characterized. Both wavelength and angle multiplexing, as well as its combination, will be used to prov ...

    SBIR Phase I 1997 Department of DefenseOffice of the Secretary of Defense
  7. Composite Preburner & Turbopump Housing Materials and Process

    SBC: WILSON COMPOSITE TECHNOLOGIES            Topic: N/A

    Composite technology exists for application to cryogenic fluid storage without an interface liner. This technology is being applied to an LH2 storage pressure vessel under Air Force Contract F29601-C-0217. This proposal outlines a program to transfer the LH2 composite technology to liquid rocket engine components. This proposal will address requirements for feed system assemblies, such as prebu ...

    SBIR Phase I 1997 Department of DefenseOffice of the Secretary of Defense
  8. Computer Enhanced Eddy Current Detection of Hidden Substructure Edges and Holes

    SBC: American Research Corporation of Virginia            Topic: N/A

    N/A

    SBIR Phase I 1997 Department of DefenseOffice of the Secretary of Defense
  9. CONTROL ROOM INLEAKAGE TEST

    SBC: Lagus Applied Technology Inc.            Topic: N/A

    A SIMPLIFIED RECONNAISSANCE-TYPE TEST IS PROPOSED THAT UTILIZES THE TECHNIQUES OF TRACER GAS VENTILATION TESTING TO QUANTIFY THE UNFILTERED AIR INLEAKAGE INTO AN OPERATING NUCLEAR POWER PLANT CONTROL ROOM. THE TEST WILL BE DEVELOPED TO ENCOMPASS THE FIVE BASIC TYPES OF CONTROL ROOM EMERGENCY VENTILATION SYSTEMS. A THOROUGH ERROR ANALYSIS WILL ALSO BE UNDERTAKEN. A DETAILED TESTING PROTOCOL SUITABL ...

    SBIR Phase I 1994 Nuclear Regulatory Commission
  10. Correlation System for Security Validation and Verification using an Encoded Phase Mask

    SBC: Metrolaser, Inc.            Topic: N/A

    Verification technologies are needed to confirm the identify of perso nnel and to validate the authenticity of manufactured products. Rapid advances in computers, printers, scanners, and copiers have made it increasingly simple to reproduce security emblems traditionally used for verification and authentication. Even holograms, once considered impenetrable, are now routinely counterfeited using t ...

    SBIR Phase I 1996 Department of DefenseOffice of the Secretary of Defense
US Flag An Official Website of the United States Government