You are here

Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY24 is not expected to be complete until March, 2025.

Download all SBIR.gov award data either with award abstracts (290MB) or without award abstracts (65MB). A data dictionary and additional information is located on the Data Resource Page. Files are refreshed monthly.

The SBIR.gov award data files now contain the required fields to calculate award timeliness for individual awards or for an agency or branch. Additional information on calculating award timeliness is available on the Data Resource Page.

  1. A Compact X-Ray Laser

    SBC: Tetra Corporation            Topic: N/A

    The advanced technology described in this proposal promises to increase the performance of laboratory and, specifically, tabletop x-ray lasers by up to an order of magnitude. Such gains in performance coupled with compact technology will lead to the introduction of the world s first table-top, commercial x-ray laser. Tetra proposes to develop an advanced driver for the laboratory laser based upo ...

    SBIR Phase I 1996 Department of DefenseMissile Defense Agency
  2. Adaptive Signal Conditioning and Calibration of Microelectromechanical Systems (MEMS)

    SBC: IC TECH, INC.            Topic: N/A

    A strong analogy exists between today's MEMS device and the first prototypes of the transistor. Research and development in semiconducto devices made the integration of millions of transistors into a single chip possible. It is anticipated that similar market forces will deman the integration of hundreds and later thousands of MEMS based sensors and actuators onto the same substrate in the next de ...

    SBIR Phase I 1997 Department of DefenseMissile Defense Agency
  3. A Detection System for Determining the Concentration, Size, and Depth of Buried Radioactive Material

    SBC: Shonka Research Associates            Topic: N/A

    N/A

    SBIR Phase II 1996 Nuclear Regulatory Commission
  4. Advanced Metal Powder Manufacture for MLCC Applications

    SBC: NANOCHEM RESEARCH, INC.            Topic: N/A

    Sensors, capacitors, and conducting features such as resistors and capacitors on circuit boards are produced from metal and ceramic powders 1-12 These powders are manufactured by liquid phase precipitation routes which often start with reduction of metal salts or by solid-state routes where solid reactants are mixed, heated and then milled. The solid-state processing is generally repeated several ...

    SBIR Phase I 1997 Department of DefenseMissile Defense Agency
  5. Advanced Projectile Diverters for Strategic Defense and Theater Missile Defense Miniature Interceptor Applications

    SBC: Tg&c Assoc., Inc.            Topic: N/A

    This proposal addresses the exploratory development and evaluation of novel thin film and/or monolithic detonators as diverters for guided spinning projectile use. A number of such detonators comprise a diverter technology termed RMDM, (for Ring Matrix Diverter Module) which, along with the SSPG (for Small Spinning Projectile Guidance) seeker, forms the basis for inexpensive miniature guided proje ...

    SBIR Phase I 1997 Department of DefenseMissile Defense Agency
  6. Application of a Novel Micromachining Process to Millimeter Wave Circuit Fabrication

    SBC: MICROFAB (WASVA MILLIMETER WAVE)            Topic: N/A

    MicroFab Research (MFR, Inc.) proposes to apply the techniques of micromachining to aid in the fabrication of millimeter wave components, thereby reducing manufacturing expenses. Many microwave applications such as radar and communication systems would be improved by shifting to higher frequencies, provided new lower cost manufacturing techniques can be found. A manufacturing technique is presente ...

    SBIR Phase I 1997 Department of DefenseMissile Defense Agency
  7. Bonding of Dissimilar Materials Using Pulsed Power

    SBC: UTRON, Inc.            Topic: N/A

    BMDO seeks development of novel low-to-no outgassing joining/bonding techniques for advanced composites. Explosive welding, employing actual chemical explosives, is a versatile process that can be used, in principle, with any two materials. In some situations involving difficult materials, explosive bonding is the only practical joining method. Typically, a layer of explosive is carefully coated o ...

    SBIR Phase I 1997 Department of DefenseMissile Defense Agency
  8. Carbide Electrodes for High Power Ultracapacitors

    SBC: T/J Technologies, Inc.            Topic: N/A

    In this project we will develop processes for fabricating new high surface area (HSA) ceramic electrode materials. These processes will be extensions of processes developed for producing carbon sieves. The new materials will be similar but superior to HSA molybdenum nitride electrodes developed recently by T/J Technologies, Inc. Carbide based electrodes produced by this new process will significan ...

    SBIR Phase I 1996 Department of DefenseMissile Defense Agency
  9. Comprehensible Descriptions for Fast Processing of Image Data

    SBC: DATAMAT SYSTEMS RESEARCH, INC.            Topic: N/A

    The proposed effort will apply advanced methods of hybrid learning to problems of detection and identification of sensory events (e.g., boost phase evens). Our approach aims at building a vision system capable of hybrid learning, in which symbolic (rule-based) and subsymbolic (neural network) strategies are integrated to achieve high efficiency and accuracy both in learning human comprehensible se ...

    SBIR Phase II 1997 Department of DefenseMissile Defense Agency
  10. Comprehensible Descriptions for Fast Processing of Image Data

    SBC: DATAMAT SYSTEMS RESEARCH, INC.            Topic: N/A

    N/A

    SBIR Phase I 1996 Department of DefenseMissile Defense Agency
US Flag An Official Website of the United States Government