You are here

Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY20 is not expected to be complete until September, 2021.

Download all SBIR.gov award data either with award abstracts (290MB) or without award abstracts (65MB). A data dictionary and additional information is located on the Data Resource Page. Files are refreshed monthly.

  1. Development of a Compact Electron Beam Accelerator

    SBC: MICROWAVE TECHNOLGIES, INC.            Topic: N/A

    N/A

    SBIR Phase I 1997 Department of DefenseMissile Defense Agency
  2. Ultrahigh Quality, Single-Crystal Bulk Silicon Carbide

    SBC: INTRINSIC SEMICONDUCTOR CORP.            Topic: N/A

    Silicon carbide materials will revolutionize semiconductor devices for military and commercial markets. The material's wide bandgap, high electric field breakdown, high thermal conductivity give SiC capabilities that far exceed those of silicon or gallium arsenide. Despite significant progress in silicon carbide development, fundamental defects--most prominently micropipes--persist. If SiC is to s ...

    SBIR Phase I 1997 Department of DefenseMissile Defense Agency
  3. Optimal SiC Source Powder for Bulk SiC Growth

    SBC: INTRINSIC SEMICONDUCTOR CORP.            Topic: N/A

    The properties of single-crystal silicon carbide are such that electronics devices from this material have demonstrated remarkable performance characteristics. Despite the material's promise, the material has not yet found acceptance in mainstream device markets because of the material's high cost, among other reasons. This Phase I SBIR proposes an SiC source powder with unique properties which wi ...

    SBIR Phase I 1997 Department of DefenseMissile Defense Agency
  4. Novel Technology for Electronic Multilayer Devices

    SBC: Sumi Tech, Inc.            Topic: N/A

    A novel technological approach was recently devised by Sumi Tech engineers to fabricate multilayer electronic components, which enables the manufacture of devices with very high volumetric efficiency and reliability. Inexpensive electrode materials such as copper, or aluminum are potential candidates, since the process takes place at relatively low ambient temperature (e.g., less than 400 C), thus ...

    SBIR Phase I 1996 Department of DefenseMissile Defense Agency
  5. Power Laser for Eyesafe Coherent Lidar

    SBC: COHERENT TECHNOLOGIES, INC.            Topic: N/A

    High power diode-pumped 2 micron lasers are of great interest for a variety of lidar applications, including long range hard target tracking and space-based coherent laser radar systems operating in the eye-safe region of the spectrum. Lidar modeling suggests that 0.5-1 J/pulse energies at pulse repetition frequencies of about 40 Hz will be sufficient to meet many lidar mission requirements. CTI h ...

    SBIR Phase I 1995 Department of DefenseMissile Defense Agency
  6. Fabrication of Quantum Effect Transistors and Switches

    SBC: Lynntech Inc.            Topic: N/A

    Using a combination of novel and traditional fabrication techniques, ultra-short gate (110nm) FETs have been fabricated which are sufficiently small, and have sufficiently low capacitance that single electron gating is observed. The devices also exhibit I-V hysteresis in the single electron switching as well as in the classical operation regime (from two different mechanisms). It is expected that ...

    SBIR Phase I 1995 Department of DefenseMissile Defense Agency
  7. High-Density, Reconfigurable Optical Routing Interconnects

    SBC: Macro-vision Communications,            Topic: N/A

    High-density reconfigurable optical routing interconnect is introduced in this SBIR program for optical signal processing. This structure is based on three key features: 1) Polarization manipulation using 2-D spatial light modulators; 2) polarization complementary geometry; and 3) the throw-away undesired optical energies design. The polarization manipulation provides the basis for "no-moving" par ...

    SBIR Phase I 1997 Department of DefenseMissile Defense Agency
  8. Position Sensor for Segmented Adaptive Optics

    SBC: Blue Line Engineering Co            Topic: N/A

    There is a serious need for new types of position sensors for use with adaptive optics systems which employ segmented mirrors. In particular, sensors which enable the system to control and maintain the phase matching of the mirrored surfaces of adjacent segments to accuracies of a few nanometers are needed. Blue Line Engineering Co. proposes to develop a novel type of sensor which will be suitable ...

    SBIR Phase I 1995 Department of DefenseMissile Defense Agency
  9. Ion-Implanted 2-D MESFET Technology for Wireless Communications

    SBC: Advanced Device Technologies,            Topic: N/A

    This Phase I project has two primary objectives. The first objective is to evaluate the feasibility of a fully ion implanted fabrication process based on the heterodimensional 2-D MESFET. The new device, the 2-D JFET, will have p+ ion implanted sidegates which laterally modulate a thin, highly doped n-type conducting channel. The 2-D JFET should have excellent high speed, low power characteristics ...

    SBIR Phase I 1997 Department of DefenseMissile Defense Agency
  10. Nitride, Carbide and Non-Oxide In Situ Coatings Using RECVD,A New CVD Method

    SBC: CCVD, Inc dba MicroCoating Technologies (MCT)            Topic: N/A

    Currently, thermal spray (flame and plasma spray) is the only single step method of applying most metal and non-oxide ceramic coatings to large objects. These coatings are usually of a low quality, and thin films cannot be applied. An in situ deposition technique that inexpensively and easily applies nitrides, carbides and other non-oxide thin or thick films in an environmentally friendly manner i ...

    SBIR Phase I 1997 Department of DefenseMissile Defense Agency
US Flag An Official Website of the United States Government