List

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for the given year is not complete until April of the following year. Annual Reports data is a snapshot of agency reported information for that year and hence might look different from the live data in the Awards Information charts.

  1. "Big Eye" Binoculars Extension Kit for Automating Bearing/Range Measurement and Image Storage

    SBC: R3 Digital Sciences, Inc.            Topic: 823

    TECHNICAL ABSTRACT: R3 Digital Sciences, Inc. (R3-DS) proposes to develop and commercialize an extension kit for "Big-Eye" and other binoculars that will automatically compute and store distance and bearing assessments by combining vertical reticle and stereoscopy measurement with motion analysis techniques. It will also capture and store photographic and video evidence of what the observer sees t ...

    SBIR Phase I 2018 National Oceanic and Atmospheric AdministrationDepartment of Commerce
  2. 120-X-2 Unmanned Aircraft System-Borne Atmospheric & Sea Surface Temperature (SST) Sensing

    SBC: Piasecki Aircraft Corporation            Topic: 84

    To capture critical weather and SST data in the Tropical Cyclone Boundary Layer (TCBL), Piasecki Aircraft proposes to evaluate existing meteorological sensor packages, integrate new off-the-shelf MEMS sensors, and design an air-launched UAS to improve the resolution of observations captured in the TCBL. Capturing latent and sensible heat fluxes can be achieved reliably with a powered UAS (compare ...

    SBIR Phase I 2014 Department of CommerceNational Oceanic and Atmospheric Administration
  3. 3-D Digital Image Correlation Based Non-Destructive Testing System for Qualification of Additive Manufacturing Parts

    SBC: X-wave Innovations, Inc.            Topic: NA

    NIST's seeks a high resolution DIC technology for qualification of complex AM parts. To meet this critical need, X-wave Innovations Inc. proposes to develop a 3-Dimentional Digital Image Correlation (3-D DIC) based NDT system. The proposed effort builds upon the success of XII in developing a variety of NDT technologies (including DIC system) for advanced materials evaluation. The success of the p ...

    SBIR Phase I 2017 Department of CommerceNational Institute of Standards and Technology
  4. 3-D Materials Characterization Using Structured Illumination in the SEM

    SBC: Advanced Microscopy Techniques            Topic: N/A

    Microscopic measurement of surface topography is a continuing need in microfabrication technology and materials research. The aim of this research is to adapt the scanning electron microscope (SEM) to the quantitative measurement of a wide range of surface structures. The SEM is a widely used measurement tool in materials science and semiconductor fabrication. The SEM's strength is that it prov ...

    SBIR Phase I 1995 Department of Commerce
  5. 3-D Printing of Opto-Electronic Components on Flexible Substrates

    SBC: Gemfire Corporation            Topic: N/A

    Not Available The technique of screen printing has been demonstrated to be of practical benefit in numerous engineering applications. Over the past two decades, these benefits have been widely recognized by the electronics industry, as evidenced by the flourishing fields of screen-printed thick-film electronics. Multilayer circuits are now manufactured by the sequential deposition of conductive an ...

    SBIR Phase II 1999 Department of Commerce
  6. 3-D Printing of Opto-Electronic Components on Flexible Substrates

    SBC: Gemfire Corporation            Topic: N/A

    The technique of screen printing has been demonstrated to be of practical benefit in numerous engineering applications. Over the past two decades, these benefits have been widely recognized by the electronics industry, as evidenced by the flourishing fields of screen-printed thick-film electronics. Multilayer circuits are now manufactured by the sequential deposition of conductive and resistive pa ...

    SBIR Phase I 1998 Department of Commerce
  7. 300 mm High Density Temperature Probe Card for Wafer- Level Reliability Testing

    SBC: Celadon Systems Inc.            Topic: N/A

    Historical methods of reliability assessment are less and less effective as device sizes shrink. Already researchers are unable to package the many advanced devices because the act of cutting the wafer and the packaging operation pre-stresses or destroys the devices resulting in unreliable test results. Additionally the increasing cost of fabricating a wafer with advanced integrated circuit techno ...

    SBIR Phase I 2010 Department of CommerceNational Institute of Standards and Technology
  8. 3D Tip Characterization and Surface Reconstruction

    SBC: Nanometrology International, Inc.            Topic: 9070168TT

    Nanometrology International, Inc. (NMI) proposes to demonstrate the feasibility of 3-dimensional (3D) characterization of nanoscale objects using scanning probe microscopy (SPM) with a measurement uncertainty of less than 0.7 nm. To accomplish this task, we propose a novel method of 3D tip characterization and use of an innovative surface reconstruction algorithm recently introduced by NIST and th ...

    SBIR Phase I 2011 Department of CommerceNational Institute of Standards and Technology
  9. 3DR Superpressure Balloon for Development of In-Situ Environmental Sensors

    SBC: GSSL Inc            Topic: N/A

    In-situ measurement of meteorological, atmospheric chemistry, and oceanic parameters for regional models would aid greatly in the understanding of critical processes and provide the necessary data for national policy decisions on significant environmental issues. three Dimensional Reinforced (3DR) membranes have the ability to offer a dramatic reduction in the required envelope mass for balloons d ...

    SBIR Phase I 2002 Department of Commerce
  10. 3DR Superpressure Balloon for Development of In-Situ Environmental Sensors

    SBC: GSSL Inc            Topic: N/A

    In-situ measurement of meteorological, atmospheric chemistry, and oceanic parameters for regional models would aid greatly in the understanding of critical processes and provide the necessary data for national policy decisions on significant environmental issues. three Dimensional Reinforced (3DR) membranes have the ability to offer a dramatic reduction in the required envelope mass for balloons d ...

    SBIR Phase II 2002 Department of Commerce

Agency Micro-sites

SBA logo
Department of Agriculture logo
Department of Commerce logo
Department of Defense logo
Department of Education logo
Department of Energy logo
Department of Health and Human Services logo
Department of Homeland Security logo
Department of Transportation logo
Environmental Protection Agency logo
National Aeronautics and Space Administration logo
National Science Foundation logo
US Flag An Official Website of the United States Government