You are here

Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY20 is not expected to be complete until September, 2021.

  1. Commercializing the Effective K-3 Assessment to Instruction (A2i) Intervention to Reduce Cost and to Scale Access to the Benefit of More Students

    SBC: Learning Ovations, Inc.            Topic: N/A

    Purpose: Students who fail to achieve proficient levels of literacy are at increased risk for grade retention, referral to special education, and dropping out of high school. The kindergarten through 3rd grade years are particularly important for students to gain a strong foundation in reading as those who continue to struggle with reading are significantly less likely to achieve reading proficien ...

    SBIR Phase I 2014 Department of Education
  2. Commercializing the Effective K-3 Assessment to Instruction (A2i) Intervention to Reduce Cost and to Scale Access to the Benefit of More Students

    SBC: Learning Ovations, Inc.            Topic: N/A

    Purpose: Students who fail to achieve proficient levels of literacy are at increased risk for grade retention, referral to special education, and dropping out of high school. The kindergarten through 3rd grade years are particularly important for students to gain a strong foundation in reading as those who continue to struggle with reading are significantly less likely to achieve reading proficien ...

    SBIR Phase II 2014 Department of Education
  3. CFD-Based Over-Determined Trim Analysis for Optimum Aerodynamic Efficiency

    SBC: Zona Technology, Inc            Topic: A304

    The overall objective of this Phase I project is to develop a nonlinear trim module in FUN3D for enabling the determined and over-determined trim analyses to be performed by FUN3D with static aeroelastic effects. Based on an optimization formulation, the over-determined trim analysis can determine the optimum control surface scheduling of multiple control surfaces to achieve the best aerodynamic e ...

    SBIR Phase I 2014 National Aeronautics and Space Administration
  4. Integration of Complex Geometry, 3D Woven Preforms via Innovative Stitching Technique

    SBC: T.E.A.M., INC.            Topic: H701

    Thick, 3D woven carbon/phenolic composites offer potential improvement over legacy thermal protection systems (TPS) for re-entry vehicle heat shield applications. However due to the scale and complexity of typical re-entry vehicle structures, it is likely that multiple 3D woven panels would need to laid up to create the overall heat shield, creating a potential weak spots at the panel joints. ...

    SBIR Phase I 2014 National Aeronautics and Space Administration
  5. Operationally Responsive Spacecraft Subsystem

    SBC: Saber Astronautics, LLC            Topic: H601

    Saber Astronautics proposes spacecraft subsystem control software which can autonomously reconfigure avionics for best performance during various mission conditions. The approach is to construct performance metrics from spacecraft health and welfare telemetry and learn their relationships in a probabilistic, multi-modal model called a "System Map". In this way the relationships between consumable ...

    SBIR Phase I 2014 National Aeronautics and Space Administration
  6. Deployable Solar Energy Generators for Deep Space Cubesats

    SBC: NANOHMICS INC            Topic: Z2001

    Cubesats require highly compact technologies to maximize their effectiveness. As cubesats are expected to be low-cost and, relative to the space industry, mass produced, their technologies should be simple to manufacture, yet achieve aerospace quality standards. This proposal aims to describe a novel high-efficiency (i.e., comparable to solar panels) fabricated power supply for cubesats and othe ...

    SBIR Phase I 2014 National Aeronautics and Space Administration
  7. > 1,000 W/kg Rad-Hard, High-Voltage PV Blanket at < $50/W IMM Cell Cost

    SBC: MARK O'NEILL, LLC            Topic: Z101

    The innovation is a new type of Stretched Lens Array (SLA) with a much thinner, lighter and more robust Fresnel lens than prior versions. The new lens enables a full blanket-level specific power > 1,000 W/kg, including lenses, the complete PV cell circuit (including cells, encapsulation, high-voltage insulation, and heavy radiation shielding), and waste heat rejection radiator. The new SLA array ...

    SBIR Phase I 2014 National Aeronautics and Space Administration
  8. Simulating Nonlinear Dynamics of Deployable Space Structures

    SBC: MotionPort, LLC            Topic: H502

    To support NASA's vital interest in developing much larger solar array structures over the next 20 years, MotionPort LLC's Phase I SBIR project will strengthen validated modeling analysis and simulation techniques by developing a vertical application to simulate the nonlinear dynamics of the various stages of deployable space structures. This application which will support RecurDyn Multi-Body Dyn ...

    SBIR Phase I 2014 National Aeronautics and Space Administration
  9. Advancing High Energy Lithium-Sulfur Batteries

    SBC: Yardney Technical Products, Inc.            Topic: Z102

    Lithium-Ion batteries have been a main source of energy for many aerospace applications over the past decade. Future space missions are facing a number of challenging requirements, including significant increase in specific energy, approaching 500 Wh/kg, and energy density of 700 Wh/l at cell level. Compared to state-of-the-art technology today, a reduction in mass and volume are necessary, along ...

    SBIR Phase I 2014 National Aeronautics and Space Administration
  10. Additive Manufacturing Synthesis of Novel Materials for 3000 Degree

    SBC: ATS-MER, LLC            Topic: H504

    Environmentally durable material systems capable of operating at temperatures from 1500 to 3000?C while maintaining structural integrity are enabling for future hot structure hypersonic vehicles. State-of-the-art ceramic matrix composite CMC's and other established refractories lack stability at these high temperatures. The plasma transferred arc (PTA) additive manufacturing (AM) process has dem ...

    SBIR Phase I 2014 National Aeronautics and Space Administration
US Flag An Official Website of the United States Government