You are here

Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY20 is not expected to be complete until September, 2021.

  1. The Design of a Low Cost, Rapidly Deployable, Sirborne Harmful Algal Bloom Identification Technology (HABIT) Sensor

    SBC: Aethon Intelligence, LLC            Topic: 834

    The optimal design for a rapidly-deployable, airborne HAB identification sensor requires the determination of the minimum spectral, spatial, dynamic range, and deployment capabilities necessary to achieve the goal of operational detection. This sensor must be capable of rendering a positive identification, with a low false alarm rate, in optical shallow waters, where the bottom is visible in the ...

    SBIR Phase I 2005 Department of Commerce
  2. Analysis Tools for Detection and Diagnosis of Biological Threats

    SBC: ALPHA-GAMMA TECHNOLOGIES, INC.            Topic: CBD04113

    DNA microarray technology, in combination with statistical and predictive modeling tools, could be used to evaluate thousands of genes against distinct gene expression patterns induced by chemical/biological agents to provide early identification and speed therapeutic intervention. The overall objective of this Phase II effort is to leverage existing public domain resources and commercial tools t ...

    SBIR Phase II 2005 Department of DefenseOffice for Chemical and Biological Defense
  3. Nano Alumina Air Filtration Media

    SBC: ARGONIDE CORP.            Topic: CBD05102

    NanoCeramr filtration media has been developed for purification of water. The active component is a nano alumina fiber only 2 nanometers in diameter. When dispersed with microglass fibers as part of a non-woven fibrous filter it is capable of retaining sub-micron and nanosize particles smaller than virus while maintaining a high flux. Such media has a dirt holding capacity tens of times greater ...

    SBIR Phase I 2005 Department of DefenseOffice for Chemical and Biological Defense
  4. Construction of a Force Probe for Characterization of Microscale Features

    SBC: INSITUTEC, INC.            Topic: N/A

    The pressing need exists within industry to accurately measure high aspect ratio microscale structures. For example, diesel injector nozzles are manufactured with microscale holes ranging from 50-200 micrometers in diameter and 3-5 mm depths. One fundamental challenge is to nondestrucvely measure these features in order to validate models, enhance manufacturing processes, and reduce fuel emissions ...

    SBIR Phase I 2005 Department of CommerceNational Institute of Standards and Technology
  5. Handheld Photoacoustic Chemical Agent and Toxic Industrial Material Detector

    SBC: MANNING APPLIED TECHNOLOGY            Topic: CBD05112

    Manning Applied Technology proposes to develop a handheld infrared spectrometer, ideally suited to detection of airborne chemical agents at and below permissible exposure limits. This approach offers unmatched sensitivity and specificity for detection of all types of chemical vapors. The instrument is modular, rugged, compact and highly sensitive. Volume pricing will be less than $1000 each. ...

    SBIR Phase I 2005 Department of DefenseOffice for Chemical and Biological Defense
  6. Active Mixing of Polymers in a Dispensing Head

    SBC: nScrypt, Inc.            Topic: N/A

    A method to take three polymers with varying viscosities and mixing those polymers together at the point of interest or more specifically through a micro dispensing nozzle, is being proposed. An active mixing scheme to ensure proper mixing at the pen tip is a feasible approach to this problem. The materials being mixed will not only range in viscosity but also in particle loading, which will be ha ...

    SBIR Phase I 2005 Department of CommerceNational Institute of Standards and Technology
  7. Ultra-High Vacuum Compatible Wavelength Dispersive X-ray Spectrometer

    SBC: PARALLAX RESEARCH INC            Topic: N/A

    Parallax Research, Inc. proposes to build an Ultra-High Vacuum compatible Wavelength Dispersive X-ray Spectrometer (WDS) that can be used on small spot Auger, XPS, TEM and FESEM analytical instruments for elemental analysis. The effort draws upon Parallax's experience in designing WDS systems for Scanning Electron Microscopes (SEM) and for XRF. This new type of x-ray spectrometer will eliminate th ...

    SBIR Phase II 2005 Department of CommerceNational Institute of Standards and Technology
  8. Hermetic Textile Closure Hardware System

    SBC: SIGMA K CORP            Topic: CBD04110

    Effective collective protection fabrics must have a reliable closure system. During our Phase I Work Plan, Sigma-K began developing a Hermetic Textile Closure Hardware (HATCH) system. The HATCH combines both a magnetic and geometric self locking mechanism that will provide a hermetic seal when closed. Our current Phase I successes include developing self closing samples that can provide a hermetic ...

    SBIR Phase II 2005 Department of DefenseOffice for Chemical and Biological Defense
  9. Critical Data Processing for Chemical Warfare Simulant Field Testing- Advanced Data Fusion

    SBC: Torch Technologies, Inc.            Topic: CBD05110

    To properly measure (and understand) the performance of a standoff detector, properties of the challenge cloud must be known. Meteorological models, such as HPAC and VLSTRACK, have proven to be reasonably good tools for predicting cloud properties. However, a problem with these tools is that they deliver ensemble averages and may not describe a specific cloud to the detail required. The Dugway ...

    SBIR Phase I 2005 Department of DefenseOffice for Chemical and Biological Defense
  10. NANOMETER-SIZE STEP HEIGHT TEST STRUCTURES

    SBC: Advanced Technologies/Laboratories Intl            Topic: N/A

    MCNC PROPOSES A FEASIBILITY STUDY AND EVALUATION OF THREE PROMISING APPROACHES TO THE FABRICATION OF SURFACE TEST STRUCTURES ON SILICON. SURFACE FEATURES ON THE FIRST STRUCTURE WILL BE PRODUCED BY CONTROLLABLY ETCHING THERMALLYGROWN OXIDES. FEATURES ON THE SECOND WILL BE MADE BY ETCHING PIEZOELECTRIC THIN FILMS. USING THE PIEZOELECTRIC FILM AS PART OF A CAPACITOR, STEP-HEIGHT CAN BE VARIED AND PRO ...

    SBIR Phase I 1992 Department of Commerce
US Flag An Official Website of the United States Government