You are here
Award Data
The Award database is continually updated throughout the year. As a result, data for FY24 is not expected to be complete until March, 2025.
Download all SBIR.gov award data either with award abstracts (290MB)
or without award abstracts (65MB).
A data dictionary and additional information is located on the Data Resource Page. Files are refreshed monthly.
The SBIR.gov award data files now contain the required fields to calculate award timeliness for individual awards or for an agency or branch. Additional information on calculating award timeliness is available on the Data Resource Page.
-
Resin Transfer Molding of High Temperature Composites
SBC: Maverick Corporation Topic: N/AResin Transfer Molding (RTM) offers the opportunity for significant cost savings in the fabrication of polymer matrix composite structures. However, the realization of this cost savings has been limited to lower temperature (e.g. epoxy) matrix composites. The main reason for this has been that available high temperature (e.g. polymide) composites have not possessed the characteristics which make ...
SBIR Phase I 1997 Department of DefenseOffice of the Secretary of Defense -
Advanced Fasteners for Low Cost Airframe Assembly and Repair
SBC: NAVMAR APPLIED SCIENCES CORP Topic: N/AThis SBIR proposes the development of the 3/16 inch diameter "Wing-It" blind fastener. This effort will include fastening both aluminum and composite sheet material. The technical objective is to demonstrate a low-cost fastener for future aircraft as an alternative to production fasteners. The "Wing-It" fastener distributes the load in the joint over a much larger area than conventional fastene ...
SBIR Phase I 1997 Department of DefenseOffice of the Secretary of Defense -
The Marathon Transmitter: Dramatically Extending Air Time
SBC: NOVA ENGINEERING, INC. Topic: N/AThe concerted effort to digitize the battlefield via digital wireless communications translates these data transfer requirements to the handset since transceivers can now serve as network nodes. Therefore a primary ingredient to satisfying the digital wireless network demand lies in securing dramatic improvements in transmitter efficiency. Many radios include the capability to dynamically adjust ...
SBIR Phase II 1997 Department of DefenseOffice of the Secretary of Defense -
Extensible Beamformer for Portable Imaging Sonar
SBC: Q-DOT, INC. Topic: N/AQ-DOT proposes to develop a unizue, lower-power, low-cost beamformer for portable imaging sonars. The original two chip set will form 100 beams from 100 input channels. A 0.3 cm2 BiCMOS chip comprises a low noise amplifier (LNA), a time-gain control (TGC), an apodizer and a Delta-Signma modulation (ADC) for each channel. A 0.66 cm2 CMOS chip accepts 100 digital input channels and produces 100 d ...
SBIR Phase I 1997 Department of DefenseOffice of the Secretary of Defense -
Novel Matrix Addressable Sonar Transducer
SBC: Sensortex Topic: N/AThis Small Business Innovation Research Phase I will fabricate a new transducer element, which is matrix addressable, conformable and low cost. It is based on the use of a composite magnetoelectric film fabricated as a hollow cylinder. This cylinder contains both the sensing elements and the matrix-forming element. This approach builds on previous work on a composite laminar maggetoelectric mat ...
SBIR Phase I 1997 Department of DefenseOffice of the Secretary of Defense -
HLA Federation InterConnect (FedConnect) Tool Set
SBC: Spectra Research, Inc. Topic: N/AIn order to become HLA compliant, a Simulation Object Model (SOM) and interface code must be developed for every legacy model that needs to interoperate with other models in a federation. Lessons learned from the protofederation experiments proved that this is a very difficult task that can take up to three person years of effort. At this point in the HLA development, no tool set to conduct this ...
SBIR Phase I 1997 Department of DefenseOffice of the Secretary of Defense -
AgentsTools- intelligent agents for analysis and modeling
SBC: SYSTRAN FEDERAL CORP. Topic: N/ASYSTRAN, and our subcontractor , Katherine Morse of SAIC (San Diego), will design and selectively demonstrate (in Phase I), and develop and significantly demonstrate (in Phase II), a series of intelligent software agents - collectively called AgentsTools - that will effect the analysis and modeling of data collected in real-time during HLA compliant simulations. AgentsTools will be developed usin ...
SBIR Phase I 1997 Department of DefenseOffice of the Secretary of Defense -
Implementing 3-D Audio into the HLA/RTI Structure
SBC: SYSTRAN FEDERAL CORP. Topic: N/ASYSTRAN, and our partner Ball Aerospace and Technologies Corp. (BATC) - an experienced HLA user and member of the HLA Protofederation activity - will design and selectively demonstrate (in Phase I), and develop and significantly demonstrate (in Phase II) a series of techniques and processes that will allow users of idstributed simulations the ability to incorporate audio signatures, audio transmis ...
SBIR Phase I 1997 Department of DefenseOffice of the Secretary of Defense -
Porous Sol-Gel Derived Ceramic Release Agent
SBC: TPL, INC Topic: N/ABreathable release coatings that can withstand processing conditions up to 750F are needed for use on ceramic tooling. In situ removal of volatiles in solvent-based composite processing is a critical issue that will enable production of high quality parts at lower cost per part. Current release coatings meet neither the temperature nor the solvent transport requirements of solvent-based composit ...
SBIR Phase I 1997 Department of DefenseOffice of the Secretary of Defense -
Processing of High Tg Polymers for Aircraft Canopies using a Supermicrocellular Foaming Technique
SBC: WRIGHT MATERIALS RESEARCH CO. Topic: N/ACurrent fighter canopy systems are fabricated using acrylics and polycarbonates which have low use temperatures, up to 220F and 300F, respectively. Wind tunnel testing of aircraft windshield showed that the transparency surface temperatures varied from 200F to 500F. Therefore, high Tg canopy systems are needed to fully utilize advanced weapon systems. Conventional processing techniques for high ...
SBIR Phase I 1997 Department of DefenseOffice of the Secretary of Defense