You are here

Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY24 is not expected to be complete until March, 2025.

Download all SBIR.gov award data either with award abstracts (290MB) or without award abstracts (65MB). A data dictionary and additional information is located on the Data Resource Page. Files are refreshed monthly.

The SBIR.gov award data files now contain the required fields to calculate award timeliness for individual awards or for an agency or branch. Additional information on calculating award timeliness is available on the Data Resource Page.

  1. Compressive Sensing Flash IR 3D Imager

    SBC: PHYSICAL SCIENCES INC.            Topic: A15AT007

    Physical Sciences Inc. in collaboration with Colorado State University proposes to develop a compact infrared flash 3D imaging sensor employing compressive sensing (CS) approaches. The CS 3D sensor offers a combination of high range resolution (10 cm), high point cloud density (6464 format), and fast 3D image frame rates (10 Hz) in a low cost, compact form factor employing commercial off the shelf ...

    STTR Phase II 2016 Department of DefenseArmy
  2. Conductive Transmissive Coating for Enhanced-Absorption Thin Film Solar Cells

    SBC: AGILTRON, INC.            Topic: A15AT016

    Thin-film, lightweight, large-area flexible inorganic solar cells have shown promise to meet the militarys remote power needs on the battlefield. However, thin film solar cells normally have inferior conversion efficiencies due to limited absorption of sunlight by the thin active layer. Various approaches have been investigated to improve conversion efficiencies of thin film solar cells. Among the ...

    STTR Phase I 2016 Department of DefenseArmy
  3. Conformal Passivation of High Aspect Ratio HgCdTe Surfaces by ALD Using a Novel Cd-Precursor

    SBC: RADIATION MONITORING DEVICES, INC.            Topic: A13AT013

    "HgCdTe is the material of choice for high performance infrared red focal plane arrays (IRFPA) used in militarys night vision systems. One of the major problems IRFPA manufacturers face is the ineffective passivation of the highly reticulated HgCdTe detector surfaces, which results in poor performance. Furthermore, newly evolved FPA technology requires the creation of much challenging high-aspect ...

    STTR Phase II 2015 Department of DefenseArmy
  4. Development of novel wound dressing technology combining advanced hydrogel and perfusion enhancement technologies.

    SBC: Perfuzia Medical            Topic: A14AT016

    Complex wounds including traumatic, chemical, chronic or surgical wounds present a significant challenge to care givers. Wound healing, being a complex and multifaceted process, differs significantly based on the type of wound and the underlining health of the patient. It is well established that factors like impaired perfusion, infection, existence of metabolic disorders such as diabetes, bad nut ...

    STTR Phase I 2015 Department of DefenseArmy
  5. Dismounted Soldier Positioning, Navigation and Timing (PNT) System Initialization

    SBC: Integrated Solutions for Systems, Inc.            Topic: A17AT017

    Integrated Solutions for Systems, Inc. (IS4S) and teammate Auburn University (AU) propose to develop a PNT initialization system for dismounted soldiers. The proposed system will enhance warfighters’ ability to operate immediately in a GPS denied environments once their mission begins and has wide commercialization potential outside of DoD. In Phase I, the feasibility and expected benefits of in ...

    STTR Phase II 2018 Department of DefenseArmy
  6. 3D Tomographic Scanning Microwave Microscopy with Nanometer Resolution

    SBC: Alcatera Inc.            Topic: A17AT008

    Scanning probe microscopy (SPM) is a technique used to detect near-field interaction when a sample is rater-scanned by a probe. Example include atomic force microscope (AFM) and scanning tunneling microscope (STM). It offers nanometric and atomic image resolution. In this field, an emerging technique, Near-Field Scanning Microwave Microscopy (SMM), utilizes microwave evanescent waves to attain the ...

    STTR Phase II 2018 Department of DefenseArmy
  7. Electronically Tunable High-Power Infrared Lasers for Standoff Detection Applications

    SBC: Pranalytica, Inc.            Topic: A14AT015

    In response to the Army STTR Topic A14A-T015 solicitation for tunable high-power LWIR lasers for standoff detection applications, Pranalytica proposed to develop a compact, rugged and highly reliable wavelength tunable quantum cascade laser (QCL) module delivering over 5W of peak power and over 0.5W of average power in the spectral region spanning from 7 to 11m. The proposed approach is based on a ...

    STTR Phase II 2016 Department of DefenseArmy
  8. EM-SMART: Electromagnetic Spectrum Monitor, Identification, and Broadcast

    SBC: Intelligent Automation, Inc.            Topic: A15AT008

    Intelligent Automation Inc. (IAI) proposes to develop and implement a two-fold spectrum monitor and broadcast system EM-SMART (Electromagnetic Spectrum Monitor, Identification and Broadcast). EM-SMART provides the electromagnetic spectrum (EMS) capability to recognize and classify blue force and red force waveforms, and the emulation capability to broadcast anticipated opposing force waveforms. Th ...

    STTR Phase I 2015 Department of DefenseArmy
  9. Energy Harvesting Fabric

    SBC: STREAMLINE AUTOMATION LLC            Topic: A15AT017

    A human produces more than 100 Watts of waste heat during normal activity. If a fraction of this heat energy can be harvested it can replace the stored chemical energy in one or more of the batteries typically carried by soldiers in the field. The current generation batteries, such as the BB2590 are bulky and rigid. The PowerFelt material developed by Wake Forest University is ideally suited for h ...

    STTR Phase I 2016 Department of DefenseArmy
  10. FRICTION STIR ADDITIVE MANUFACTURING OF TITANIUM ALLOYS FOR HIGH PERFORMANCE MILITARY APPLICATIONS

    SBC: ATS-MER, LLC            Topic: A16AT002

    Friction stir additive manufacturing (FSAM) will be utilized for repair, fabrication and processing of Titanium components and sub-assemblies for high performance military applications. The innovation will address the issue of part distortion resulting from high residual stresses imposed during traditional fusion welding based additive manufacturing techniques. In addition to enhancing dimensional ...

    STTR Phase I 2016 Department of DefenseArmy
US Flag An Official Website of the United States Government