You are here

Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY24 is not expected to be complete until March, 2025.

Download all SBIR.gov award data either with award abstracts (290MB) or without award abstracts (65MB). A data dictionary and additional information is located on the Data Resource Page. Files are refreshed monthly.

The SBIR.gov award data files now contain the required fields to calculate award timeliness for individual awards or for an agency or branch. Additional information on calculating award timeliness is available on the Data Resource Page.

  1. Triton™: Active Imaging through Fog

    SBC: SA PHOTONICS, LLC            Topic: N18AT021

    Active imaging systems are used in degraded visual environments, like those found in marine fog and other areas with a high level of attenuation and scattering from obscurants like rain, smoke and dust. These systems are still limited in range and resolution. SA Photonics is taking advantage of new eyesafe, hybrid fiber-bulk laser technology capable of high pulse energy at high repetition rate to ...

    STTR Phase II 2020 Department of DefenseNavy
  2. Decision Support for Operators of Fully Autonomous Systems using RESTORE: Robust Execution System for Trusted Operation in Relevant Environments

    SBC: SCIENTIFIC SYSTEMS CO INC            Topic: N18BT032

    SSCI and MIT (Prof. Julie Shah) propose to develop and test a system that provides real-time assurance and trust in decisions made by autonomous collaborating vehicles. The proposed system is referred to as the RESTORE (Robust Execution System for Trusted Operation in Relevant Environments) and represents a decision support tool which facilitates decision making by the operator in cases when decis ...

    STTR Phase II 2020 Department of DefenseNavy
  3. Scalable Manufacturing of Composite Components using Nanostructured Heaters

    SBC: METIS DESIGN CORP            Topic: N18BT031

    Manufacturing of structural composites traditionally employs autoclaves to achieve high quality parts, including high fiber-volume-fractions and low porosity. A laminate comprised of stacked prepreg plies are cured under a vacuum in addition to ~7 bar of pressure to prevent formation of voids, particularly in interlaminar (inter-sheet/ply) regions. However, manufacturing composites within an autoc ...

    STTR Phase II 2020 Department of DefenseNavy
  4. Optimization of Fatigue Test Signal Compression Using The Wavelet Transform

    SBC: ATA ENGINEERING, INC.            Topic: N18BT029

    ATA Engineering has developed a wavelet-based damage squeezing methodology for generating optimally compressed fatigue test signals that produce an equivalent amount of fatigue damage in a predictably reduced amount of time compared to the baseline (uncompressed) signals. Fatigue-critical signal characteristics (e.g., magnitude, phase, frequency, and sequencing relationships) are identified in the ...

    STTR Phase II 2020 Department of DefenseNavy
  5. Detection Rate Improvements Through Understanding and Modeling Ocean Variability

    SBC: Ocean Acoustical Services and Instrumentation Systems, Inc.            Topic: N18AT002

    The littoral environment is especially demanding on tactical sonar systems, in large part because the spatial and temporal variability imposes sonar system operating conditions of a nature and with a scale heretofore not encountered in the open oceans. Recent Office of Naval Research (ONR) sponsored basic research as well as fleet exercises have shown that littoral environments tactically importan ...

    STTR Phase II 2020 Department of DefenseNavy
  6. Non-Destructive Evaluation (NDE) of Missile Launcher Ablatives

    SBC: TEXAS RESEARCH INSTITUTE , AUSTIN, INC.            Topic: N18AT011

    MK-41 VLS exhaust paths are lined with ablative insulation that chars and ablates with each missile firing. There is no way to inspect, in-situ, chemical and physical changes to the ablatives. Such measurements are complicated because ablative materials: vary with location, are low density, and degrade non-linearly with firings.Failure of VLS insulation is not an option – but the usage life of t ...

    STTR Phase II 2020 Department of DefenseNavy
  7. Full Featured Low-Cost HMS for Combatant Craft

    SBC: QUALTECH SYSTEMS, INC.            Topic: N18AT015

    Qualtech Systems, Inc. (QSI), in collaboration with Vanderbilt University (VU) proposes to develop a state-of-the art Health Management System (HMS) system consisting of a small form factor GPS-enabled onboard computer, a small display for crew, and sensors for boat and engine vibration, OBD data, engine oil quality monitoring, and battery health monitoring. The HMS system will provide Wi-Fi and w ...

    STTR Phase II 2019 Department of DefenseNavy
  8. Protocol Feature Identification and Removal

    SBC: P & J ROBINSON CORP            Topic: N18AT018

    Protocols used for communication suffer bloat from a variety of sources, such as support for legacy features or rarely used (and unnecessary) functionality. Traditionally, the Navy subscribes to a blanket adoption of a standard protocol "as is". Unnecessary features are active and can be accessed by both internal and external systems creating security vulnerabilities. PJR Corporation's (PJR's) Pha ...

    STTR Phase II 2019 Department of DefenseNavy
  9. Additive Manufacturing for Naval Aviation Battery Applications

    SBC: STORAGENERGY TECHNOLOGIES INC            Topic: N18AT008

    The objective of the efforts being proposed is to develop high energy density and power density batteries with long cycle life by high-speed additive manufacturing technologies.

    STTR Phase II 2019 Department of DefenseNavy
  10. TOPMAST II- Repurposing Computational Analyses of Tactics for Training Assessments

    SBC: APTIMA INC            Topic: N18AT003

    As the complexity of threats and emerging warfare capabilities increase, so do the number of Tactics, Techniques, and Procedures (TTPs) and the corresponding training regimes. Instructors are increasingly in need of automated tools to enable training that scales with complexity. Aptima, Inc., and our partners, Aviation Systems Engineering Company, Inc. (ASEC) and the University of Southern Califor ...

    STTR Phase II 2019 Department of DefenseNavy
US Flag An Official Website of the United States Government