You are here

Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY24 is not expected to be complete until March, 2025.

Download all SBIR.gov award data either with award abstracts (290MB) or without award abstracts (65MB). A data dictionary and additional information is located on the Data Resource Page. Files are refreshed monthly.

The SBIR.gov award data files now contain the required fields to calculate award timeliness for individual awards or for an agency or branch. Additional information on calculating award timeliness is available on the Data Resource Page.

  1. Multiphysics Modeling of Dynamic Combustion Processes Using Pareto-Efficient Combustion Framework

    SBC: STREAMLINE NUMERICS, INC.            Topic: AF18BT010

    The objective is to develop zonal multi-physics capability for turbulent combustion simulations. The foundation of the proposed work is a novel Pareto-Efficient Combustion (PEC) framework for fidelity-adaptive combustion modeling. The PEC model utilizes a combustion submodel assignment, combining the low-cost flamelet-based models with the more expensive finite rate chemistry models where necessar ...

    STTR Phase I 2019 Department of DefenseAir Force
  2. Scalable Manufacturing of Composite Components Using Nanostructured Heaters

    SBC: METIS DESIGN CORP            Topic: N18BT031

    Manufacturing of structural composites traditionally employs autoclaves to achieve high quality parts, including high fiber-volume-fractions and low porosity. A laminate comprised of stacked prepreg plies are cured under a vacuum in addition to ~7 bar of pressure to prevent formation of voids, particulalry in interlaminar (inter-sheet/ply) regions. However, manufacturing composites within an autoc ...

    STTR Phase I 2019 Department of DefenseNavy
  3. Carbon Nanotube-Based Heater Coatings for Processing of Thermosetting and Thermoplastic Composites

    SBC: MAINSTREAM ENGINEERING CORP            Topic: N18BT031

    For this research program, Mainstream will collaborate with Colorado State University (CSU) to develop a nanostructured heater capable of curing aerospace grade composites out-of-autoclave (OOA). The use of autoclaves is the primary cost driver in composite manufacturing due to size limitations, long processing times, and inefficient energy usage. Therefore, the Navy is looking to develop a nanost ...

    STTR Phase I 2019 Department of DefenseNavy
  4. CRANE: Cervical Readiness Using Analytics and Non-Invasive Evaluation

    SBC: APTIMA INC            Topic: DHA18B001

    Current cervical spine assessment methodologies are focused on subjective measures (i.e. pain reports) and range-of-motion (ROM) measures that only measure maximum head excursion and reach, but not dynamic motion. Due to report bias and existing incentive

    STTR Phase I 2019 Department of DefenseDefense Health Agency
  5. Decision Support for Operators of Fully Autonomous Systems using RESTORE: Robust Execution System for Trusted Operation in Relevant Environments

    SBC: SCIENTIFIC SYSTEMS CO INC            Topic: N18BT032

    SSCI and MIT (Prof. Julie Shah) propose to develop and test a system that provides real-time assurance and trust in decisions made by autonomous collaborating vehicles. The proposed system is referred to as the RESTORE and represents a decision support tool which facilitates decision making by the operator in cases when decisions by the Collaborative Autonomy (CA) system results in deviations from ...

    STTR Phase I 2019 Department of DefenseNavy
  6. Rapid Prototyped 3D Printed Filters for CW Agent Protection

    SBC: TDA RESEARCH, INC.            Topic: A18BT018

    Defense against chemical weapons is a critical DoD requirement. An effective defense requires the development of unique respirator systems that prevent inhalation of chemical warfare (CW) agents. In addition, the protective equipment exposed to CW agents must not pose a residual hazard after use in the battlefield. Existing respirator canisters remove CW agents, but they do not self-decontaminate ...

    STTR Phase I 2019 Department of DefenseArmy
  7. Paper Spray Mass Spectrometry Cartridges with Integrated Sampling and Enrichment

    SBC: Nano Terra, Inc.            Topic: A18BT020

    PS-MS is a simple and powerful method for rapid ambient sample preparation. However, its simplicity also means separation of undesirable components (particulates and molecular interferents) is not possible. Furthermore, samples must be collected by other means (e.g., dried blood spot cards) and placed on the ticket in liquid form before analysis. Although the technique is sensitive (nanograms to t ...

    STTR Phase I 2019 Department of DefenseArmy
  8. Universal textile functionalization chemistry for molecular and particulate attachment based on a novel activation treatment

    SBC: Nano Terra, Inc.            Topic: A18BT024

    Nano Terra and the El-Shafei group (North Carolina State University) propose to demonstrate, optimize and expand a universal platform for textile functionalization. The approach is one developed in the El-Shafei group that has already been explored for its utility in cotton, nylon-cotton blends and polypropylene. The functionalization method imparts a high-level of flame retardancy (without haloge ...

    STTR Phase I 2019 Department of DefenseArmy
  9. W-Band RF Instrumentation

    SBC: MAGIQ TECHNOLOGIES, INC.            Topic: A18BT002

    In the program, MagiQ Technologies Inc., in conjunction with professor Gabriel Rebeiz from the University of California, San Diego (UCSD), is proposing a high dynamic range W-band CW/pulse RF power meter for the US Army’s application in the development of W-band radar and satellite communications. Base on unique noise reduction technique in MagiQ technologies, The power meter can operate in a hi ...

    STTR Phase I 2019 Department of DefenseArmy
  10. Design of Easy-To-Use Structural Alloy Feedstocks for Additive Manufacturing

    SBC: ELEMENTUM 3D, INC.            Topic: A18BT003

    There is a need for easy-to-use, versatile alloys for additive manufacturing that print consistently regardless of the specific process or machine, or the metallurgical and manufacturing knowledge of the user. Such capability is especially critical for soldiers to be able to make every day items on demand in the theater of war. Toward meeting this need, recent successes developing high performance ...

    STTR Phase I 2019 Department of DefenseArmy
US Flag An Official Website of the United States Government