You are here

Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY24 is not expected to be complete until March, 2025.

Download all SBIR.gov award data either with award abstracts (290MB) or without award abstracts (65MB). A data dictionary and additional information is located on the Data Resource Page. Files are refreshed monthly.

The SBIR.gov award data files now contain the required fields to calculate award timeliness for individual awards or for an agency or branch. Additional information on calculating award timeliness is available on the Data Resource Page.

  1. Fast Response Heat Flux Sensors and Efficient Data Reduction Methodology for Hypersonic Wind Tunnels

    SBC: Innoveering, LLC            Topic: AF17AT001

    There is a DoD need for the development of robust sensors to obtain temporally and spatially resolved surface temperature and heat flux measurements on test articles in blowdown and continuous hypersonic wind tunnels. These micro-heat flux sensors are required in order to better understand the state of the boundary layer of a hypersonic vehicle; to better understand boundary layer instabilities; a ...

    STTR Phase II 2019 Department of DefenseAir Force
  2. Passive Millimeter-Wave Imaging Camera System Using Optical Up-Conversion in Sparse Array Configuration

    SBC: NOVAA LTD            Topic: A18BT017

    The objective of this proposal is to enable high-sensitivity, passive imaging system of natural mm-wave emissions, which can be used as standalone or fused with other imaging modality such as conventional IR imagery in degraded environments. This is achieved through a unique antenna integrated electro-optic (EO) modulator, where received mm-wave signals modulate an optical carrier. The optical car ...

    STTR Phase I 2019 Department of DefenseArmy
  3. Rapid Prototyped 3D Printed Filters for CW Agent Protection

    SBC: TDA RESEARCH, INC.            Topic: A18BT018

    Defense against chemical weapons is a critical DoD requirement. An effective defense requires the development of unique respirator systems that prevent inhalation of chemical warfare (CW) agents. In addition, the protective equipment exposed to CW agents must not pose a residual hazard after use in the battlefield. Existing respirator canisters remove CW agents, but they do not self-decontaminate ...

    STTR Phase I 2019 Department of DefenseArmy
  4. Novel Nanocoating technology for Functional Textile

    SBC: Claros Technologies Inc.            Topic: A18BT024

    Nanoparticles represent an attractive alternative in coating processes due to their functional versatility, including surface, optical, conductive and catalytic properties. However, current processes of coating textile products with nanoparticles results in rapid loss of the nanoparticles during laundering or use, leading to a significant decrease in product durability and functionality and increa ...

    STTR Phase I 2019 Department of DefenseArmy
  5. Anticipatory Analytics for Environmental Stressors: An open community platform for accelerating environment and security research and development

    SBC: ISCIENCES LLC            Topic: A17AT021

    Environment-security researchers and practitioners must overcome several technical challenges in the course of their efforts. In the absence of an open-community platform, each researcher or institution compiles and curates their own data repositories, analytical tools, and computational environments. This results in significant duplication of effort, limits the replication and validation of resea ...

    STTR Phase II 2019 Department of DefenseArmy
  6. Tools for Parallel Adaptive Simulation of Multiphase Ballistic Flows

    SBC: SIMMETRIX, INC.            Topic: A15AT002

    This project will provide state-of-the-art predictive capabilities for simulating systems central to advancing the U.S. Army’s modernization priorities related to long-range precision fires and future vertical lift platforms. The goals of the project are to: (1) Produce geometry and meshing technologies that support the modeling and discretization techniques needed to explicitly track evolving/i ...

    STTR Phase II 2019 Department of DefenseArmy
  7. Rydberg-atom RF Sensors for Direction Finding and Geolocation (RADARS)

    SBC: COLDQUANTA, INC.            Topic: AF17AT028

    ColdQuanta, in partnership with Dr. Zoya Popovic at the University of Colorado at Boulder, proposes to develop a three-dimensional quantum-enhanced radio-frequency (RF) signal sensor and direction finder. Our approach combines Rydberg-atom-based RF electrometry and discrete lens arrays (DLAs) of planar antennas. The DLA will serve as a Fourier optic for an incident wave, and a Rydberg-atom RF elec ...

    STTR Phase II 2018 Department of DefenseAir Force
  8. W-Band RF Instrumentation

    SBC: SRICO INC            Topic: A18BT002

    W-band millimeter waves have a number of important applications, including directed energy and, more recently, 5G FR2 network development. Reliable measurements of electric fields in the W-Band, while critical to the development of these applications, have proven challenging. This proposal addresses the development of an accurate, traceable, cost effective W-band RF field strength detector. The so ...

    STTR Phase I 2019 Department of DefenseArmy
  9. Metal Additive Manufacturing with Minimal Post Processing (MaMMPP) (18-RD-116)

    SBC: UES INC            Topic: A18BT003

    Metal Additive Manufacturing (AM) research has typically addressed understanding how to maximize performance for an AM material, taking into account microstructural anisotropy, residual stress, defects (such as pores and lack of fusion defects), and surface finish. Optimizing a part then requires significant post processing such as hot isostatic pressing (HIP), heat treatment and surface finishing ...

    STTR Phase I 2019 Department of DefenseArmy
  10. Design of Easy-To-Use Structural Alloy Feedstocks for Additive Manufacturing

    SBC: ELEMENTUM 3D, INC.            Topic: A18BT003

    There is a need for easy-to-use, versatile alloys for additive manufacturing that print consistently regardless of the specific process or machine, or the metallurgical and manufacturing knowledge of the user. Such capability is especially critical for soldiers to be able to make every day items on demand in the theater of war. Toward meeting this need, recent successes developing high performance ...

    STTR Phase I 2019 Department of DefenseArmy
US Flag An Official Website of the United States Government