For best search results, use the search terms first and then apply the filters

The Award database is continually updated throughout the year. As a result, data for FY19 is not expected to be complete until April, 2020.

  1. Carbon Composites for Space Tribology

    SBC: Allcomp Inc.            Topic: N/A

    The intent of this Phase I effort was to examine the feasibility of using C-C composite for possible tribological applications in Space. In the Phase I effort, selected C-C composite materials were modified and tested for both high-speed bearing cage andslip ring/ brush applications under simulated space environments. 2D C-C cage materials were modified to reduce its pore size for lubricant retent ...

    SBIR Phase II 2001 Department of DefenseAir Force
  2. Intelligent Collision Detection and Warning System


    Phase II designs, develops, and delivers Intelligent Collision Detection and Warning System to the U.S. Air Force. The proposed Phase II project is an extension of the Phase I project ¿¿Low Cost Autonomous GPS Based Collision Avoidance System¿¿, and acontinuation of AGNC's efforts in the development of advanced avionics systems and technologies for military and commercial applications. Each ai ...

    SBIR Phase II 2001 Department of DefenseAir Force
  3. MEMS Sensors For In-situ Monitoring of Adhesive Bonded Composite Structures

    SBC: Analatom Incorporated            Topic: N/A

    The problem addressed is through-life non-destructive monitoring of adhesivelybonded structures. The concept presented is to produce a

    SBIR Phase II 2001 Department of DefenseAir Force
  4. High Brightness High Efficiency Fiber-Coupled Laser Diode

    SBC: APOLLO INSTRUMENTS, INC.            Topic: N/A

    We propose to develop a general method for the high brightness fiber-coupied laser diode system. The overall goal of this program is to deliver a brightness of 1.4 Mega Watt cm-2 sr-1 laser power system from a single fiber with a high power ourput. Thepackage will have high power density, compact dimension and light in weight. As Phase II prototype, the coupling efficiency will over 63% for whol ...

    SBIR Phase II 2001 Department of DefenseAir Force
  5. Pulse Tube Coolers for HTS Power Generation Systems

    SBC: ATLAS SCIENTIFIC            Topic: N/A

    Superconducting generators and RF magnets will be the leading technologies for high electrical power systems on aircraft, spacecraft and ground based systems in future DoD applications. These systems employ High Temperature Superconducting (HTS) materialsoperating at cryogenic temperatures. Future HTS systems will employ Yttrium Barium Copper Oxide (YBCO) which requires cooling near 65K. At pre ...

    SBIR Phase II 2001 Department of DefenseAir Force
  6. P on n HgCdTe IR Detectors

    SBC: AVYD DEVICES, INC.            Topic: N/A

    Phase I work has culminated in a p type doping approach and the formulation of a material/device fabrication approach which can assure high quantum efficiency along with a high R0A performance.Phase II work aims to optimize this p type doping/device fabrication approach and demonstrate high performance 256x256 mosaics of LWIR HgCdTe photodiodes hybridized to Si Read Out Integration Chips.

    SBIR Phase II 2001 Department of DefenseAir Force
  7. Field-Deployable Chemical Point Detection Network

    SBC: MECHATRONIC SYSTEMS LLC            Topic: N/A

    The overall objective of this proposal is to develop a high temperature, motor drive based on silicon carbide (SiC) power semiconductors for controlling a switched reluctance motor (SRM). This motor drive will be suitable for use in either anelectromechanical actuator (EMA) or an electrohydraulic actuator (EHA). The proposed Phase II effort focus is the additional research and development needed t ...

    SBIR Phase II 2001 Department of DefenseAir Force
  8. Repair of Ceramic Matrix Composite Structures

    SBC: COI Ceramics Inc            Topic: N/A

    The overall objective of this Phase II effort is to conduct an operational evaluation of a repaired Ceramic Matrix Composite (CMC) component, such as a gas path liner for an advanced F119 exhaust nozzle. CMC repair methods developed in Phase I will berefined and extended to cover three levels of damage: 1) surface ply loss, 2) delaminations and ply rupture, and 3) through-hole damage. The Phase I ...

    SBIR Phase II 2001 Department of DefenseAir Force
  9. Affordable Demonstration of Very Flexible, Large Spacecraft Structures Control and Pointing

    SBC: CSA Engineering, Inc.            Topic: N/A

    The PowerSail is a new paradigm in space systems that offers significant performance and cost improvements for on-orbit power generation. The PowerSail will co-orbit in formation with a satellite, with flexible interconnects and a robotic arm managing thelink between the two structures. The research will produce key technologies that will enable realization of the PowerSail concept. By enabling ...

    SBIR Phase II 2001 Department of DefenseAir Force
  10. SoftRide Separation System for Spacecraft

    SBC: CSA Engineering, Inc.            Topic: N/A

    Shock is a major problem for spacecraft, and is the largest dynamic load on spacecraft during launch on large launch vehicles. Shock to spacecraft during launch comes from two sources, the launch vehicle (fairing separation being one of the largest shocksources) and the spacecraft separation event. A whole-spacecraft shock isolation system will prevent shock produced by the launch vehicle from r ...

    SBIR Phase II 2001 Department of DefenseAir Force

Agency Micro-sites

SBA logo
Department of Agriculture logo
Department of Commerce logo
Department of Defense logo
Department of Education logo
Department of Energy logo
Department of Health and Human Services logo
Department of Homeland Security logo
Department of Transportation logo
Environmental Protection Agency logo
National Aeronautics and Space Administration logo
National Science Foundation logo
US Flag An Official Website of the United States Government