You are here

Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY24 is not expected to be complete until March, 2025.

Download all SBIR.gov award data either with award abstracts (290MB) or without award abstracts (65MB). A data dictionary and additional information is located on the Data Resource Page. Files are refreshed monthly.

The SBIR.gov award data files now contain the required fields to calculate award timeliness for individual awards or for an agency or branch. Additional information on calculating award timeliness is available on the Data Resource Page.

  1. A Universal Commuter Railcar Boarding Device for Use by Both Disabled and Able-bodied Individuals Configurable for all U.S. Railstation Platforms

    SBC: SAFE INC            Topic: N/A

    SAFE proposes to design and develop a boarding device for heavy rail passenger cars. The boarding system will enable the loading of all passengers regardless of mobility from a wide range of platform configurations. Once installed on a passenger railcar, that car can be used with any of four platform configurations: high level platforms close to the car, high level platforms with partial setbac ...

    SBIR Phase I 2004 Department of Transportation
  2. An Innovative Supplemental Automotive Seating System for Short-Stature Individuals

    SBC: SAFE INC            Topic: N/A

    Individuals who are of short stature face impediments when driving automobiles due to their inability to effectively operate vehicle controls, to clearly see the external roadway environment, and to properly use the vehicle restraint system. These impediments could be largely removed if a device could be developed to elevate the driver to a sitting position similar to that afforded to average hei ...

    SBIR Phase I 2004 Department of Transportation
  3. Advanced Truck for High Speed Freight Operations

    SBC: Sharma & Associates, Inc.            Topic: N/A

    During Phase I of the project, Sharma & Associates, Inc. developed a concept for a high speed freight truck intended for 70-ton, regular freight and bi-modal operation at speeds up to 150 mph. The truck uses a rigid frame and an independent, compliant, primary suspension for its basic architecture. Constant contact side-bearings and yaw dampers were also added to improve dynamic performance. Ve ...

    SBIR Phase II 2004 Department of Transportation
  4. Low Cost Transverse Rail Defect Detector

    SBC: WavesinSolids LLC            Topic: N/A

    Development of the basic EMAT-based transverse rail defect detector has progressed toward finished form, as envisioned in the original solicitation. This modification is intended to produce a demonstrable version of a 2-rail detection system with automated signal interpertation.

    SBIR Phase II 2004 Department of Transportation
  5. High-Speed Dynamic 3D Surface Mapping System

    SBC: Conrad Technologies, Inc.            Topic: N/A

    Conrad Technologies, Inc. (CTI) proposes a non-contact, dynamic 3D position sensor based on optical triangulation using multiple radiating LED targets to measure intrusion of an automobile structure into the occupant compartment during full-scale crash tests. CTI has significant experience developing non-contact measurement instruments. CTI has developed a Motion Imaging and Tracking Acquisition ...

    SBIR Phase I 2002 Department of Transportation
  6. Evaluation of Composite Joints in General Aviation Structures

    SBC: MATERIALS SCIENCES LLC            Topic: N/A

    During the Phase I program, MSC demonstrated a powerful new software tool designed for the analysis of bonded joints in General Aviation (GA) aircraft. The tool can handle the complex geometry and boundary conditions found in typical joints, and has been shown to be exceptionally accurate. An easy-to-use front end to the code was also demonstrated. In addition, Materials Sciences Corporation (M ...

    SBIR Phase II 2002 Department of Transportation
  7. Evaluation of Composite Joints in General Aviation Structures

    SBC: MATERIALS SCIENCES LLC            Topic: N/A

    During the Phase I program, MSC demonstrated a powerful new software tool designed for the analysis of bonded joints in General Aviation (GA) aircraft. The tool can handle the complex geometry and boundary conditions found in typical joints, and has been shown to be exceptionally accurate. An easy-to-use front end to the code was also demonstrated. In addition, Materials Sciences Corporation (M ...

    SBIR Phase I 2002 Department of Transportation
  8. Innovative Multi-cellular Pultruded Composite Guardrail

    SBC: Creative Pultrusions, Inc            Topic: N/A

    N/A

    SBIR Phase I 2001 Department of Transportation
  9. Innovative Multi-cellular Pultruded Composite Guardrail

    SBC: Creative Pultrusions, Inc            Topic: N/A

    N/A

    SBIR Phase II 2001 Department of Transportation
  10. Development of Light-Weight, Low-Cost Multichannels Membrane Reformer

    SBC: ATS-MER, LLC            Topic: N/A

    A novel approach for the development of a lightweight, low-cost, compact, and quick start-up on-board fuel reformer is proposed in this Phase II program. The approach is based on a novel MER¿s technique for the fabrication of multichannel mini-reactors incorporating hydrogen separating membrane. Multichannel mini-reactor shrinks the dimensions through which energy and reactants travel to their ...

    SBIR Phase II 2001 Department of Transportation
US Flag An Official Website of the United States Government