MATERIALS PROCESSING, INC.

Basic Information

5069 Martin Luther King Freeway
Fort Worth, TX, 76119

Company Profile

n/a

Additional Details

Field Value
DUNS: 119473275
Hubzone Owned: N
Socially and Economically Disadvantaged: N
Woman Owned: N
Number of Employees: 4


  1. Rifling of the Inner Diameter of Ceramic Tubes for Gun Barrel Applications

    Amount: $729,970.00

    Silicon nitride (Si3N4) based materials have the potential for use as rifled gun barrels that can provide a significant increase in barrel life, offer weight reduction, and enable the use of higher en ...

    SBIR Phase II 2006 ArmyDepartment of DefenseDepartment of Defense
  2. Novel Material and Process for Replacement of Lead Products

    Amount: $69,916.00

    Lead is a soft, low melting point, high density, and inexpensivve material that can be easily shaped. All these attributes have made lead useful in appplications such as bullets, fishing rod sinkers, ...

    SBIR Phase I 2005 Environmental Protection Agency
  3. Novel Material and Process for Replacement of Lead Products

    Amount: $69,915.81

    Lead is a soft, low melting point, high density, and inexpensive material that can be shaped easily. All of these attributes have made lead useful in applications such as bullets, fishing rod sinkers ...

    SBIR Phase I 2005 Environmental Protection Agency
  4. Novel High Temperature, High Strength, Oxide-resistant Composites for Wind Tunnel

    Amount: $99,998.00

    To produce a hypersonic flight vehicle, it is necessary to utilize an airbreating propulsion cycle. Most US aeropropulsion programs focus on the operation of a multi-mode engine with a ramjet and scr ...

    SBIR Phase I 2005 Air ForceDepartment of DefenseDepartment of Defense
  5. Rifling of the Inner Diameter of Ceramic Tubes for Gun Barrel Applications

    Amount: $69,986.00

    Silicon nitride based materials have extremely attractive property combination and is ideally suited for gun barrel applications (increased life and reduced weight). In spite of the attractive proper ...

    SBIR Phase I 2005 ArmyDepartment of DefenseDepartment of Defense
  6. Novel Hard-Nosed Penetrators

    Amount: $749,794.00

    There is currently an urgent need for the development of novel penetrator concepts capable of defeating hardened concrete reinforced targets. The use of a hard nose and high strength and high toughne ...

    SBIR Phase II 2004 Air ForceDepartment of DefenseDepartment of Defense
  7. Novel Hard-Nosed Penetrators

    Amount: $99,901.00

    There is an urgent need for the development of innovative concepts of advanced warheads for air-delivered conventional munitions to defeat host of targets, both above and buried under the ground. The ...

    SBIR Phase I 2003 Air ForceDepartment of DefenseDepartment of Defense
  8. Corrosion Resistant, Ultra-High Strength, High Toughness Steel

    Amount: $69,857.00

    "Current state-of-the-art ferrous products do not provide the desirable combination of ultra-high strength, high toughness as well as good corrosion resistance. For the carrier-based aircraft compone ...

    SBIR Phase I 2002 NavyDepartment of DefenseDepartment of Defense
  9. Powder Injection Molding for Large Military Components

    Amount: $69,924.00

    Powder injection molding (PIM) is a new technology that uses the shaping advantages of plastic injection molding but expands its applications to advanced materials such as metals, alloys, and ceramics ...

    SBIR Phase I 2001 ArmyDepartment of DefenseDepartment of Defense
  10. Ordnance Research

    Amount: $0.00

    Tungsten heavy alloys exhibiting unique property combination of high density (17-18 g/c), high strength, high ductility, and good corrosion resistance, have found applications in both military and civ ...

    SBIR Phase I 2001 Air ForceDepartment of DefenseDepartment of Defense

Agency Micro-sites

US Flag An Official Website of the United States Government