OG TECHNOLOGIES, INC.

Address

4480 VARSITY DR STE G
ANN ARBOR, MI, 48108-5007

Information

DUNS: 072247088
# of Employees: 14

Ownership Information

Hubzone Owned: N
Socially and Economically Disadvantaged: N
Woman Owned: N

Award Charts




Award Listing

  1. Capability of Rolling Efficiency for 100M High-Speed Rails

    Amount: $999,999.00

    This project is to establish the capability and sustainability of the US-based rail manufacturers by applying innovative sensing and process control for a high-efficiency practice in producing 100m hi ...

    SBIRPhase II2014Department of Energy
  2. Capability of Rolling Efficiency for 100M High-Speed Rails

    Amount: $150,000.00

    Development of high-speed rail services in the US is one of the priorities of the current administration. High-speed rails have the potential to change the nations energy consumption landscape in tra ...

    SBIRPhase I2013Department of Energy
  3. SBIR Phase II: IPPM:In-Line Piercing Process Monitoring For Seamless Tube Manufacturing

    Amount: $500,000.00

    This Small Business Innovation Research Phase II project proposes to develop an imaging based monitoring system for the piercing process used in the manufacturing of seamless steel tubes based on the ...

    SBIRPhase II2011National Science Foundation
  4. SBIR Phase I:DATA-FUSION PREDICTIVE CONTROL FOR THE FLAWS IN THE BULK OF THE CONTINUOUSLY CAST PRODUCTS

    Amount: $150,000.00

    This Small Business Innovation Research Phase I project proposes to develop the Data-fusion Predictive Control for the Flaws in the Bulk of the Continuously Cast Products ("DPC") in which (a) various ...

    SBIRPhase I2010National Science Foundation
  5. Recovery Act- Imaging-Based Optical Caliper for Objects in Hot Manufacturing Processes

    Amount: $150,000.00

    Dimension control is very important in manufacturing. Poor dimension control leads to surface defects, incorrect cross-section weight distribution, and final product straightness. There exist only pri ...

    SBIRPhase I2010Department of Energy
  6. Recovery Act- Imaging-Based Optical Caliper for Objects in Hot Manufacturing Processes

    Amount: $933,645.00

    Dimension control is very important in manufacturing. Poor dimension control leads to surface defects, incorrect cross-section weight distribution and final product straightness. The existing practice ...

    SBIRPhase II2010Department of Energy
  7. SICS: A Sensor-Based In-Line Control System for the Surfaces of Continuously Cast Slabs

    Amount: $1,000,000.00

    The current practice in the continuous casters, the primary steel making process in the US, has room to improve for better efficiency and energy savings. Each year, millions of tons of metal are scrap ...

    SBIRPhase II2010Department of Energy
  8. SBIR Phase I: IPPM: IN-LINE PIERCING PROCESS MONITORING FOR SEAMLESS TUBE MANUFACTURING

    Amount: $150,000.00

    This Small Business Innovation Research (SBIR) Phase I project seeks to verify the feasibility of an imaging based monitoring system for the piercing process used in the manufacturing of seamless stee ...

    SBIRPhase I2009National Science Foundation
  9. SICS: A Sensor-Based In-Line Control System for the Surfaces of Continuously Cast Slabs

    Amount: $100,000.00

    The current practice of continuous casting, the primary steel making process in the U.S., has room to improve, in order to achieve better efficiency and energy savings. Each year, millions of tons of ...

    SBIRPhase I2009Department of Energy
  10. STTR Phase II: An Inference Engine for an Intelligent Imaging System for Detecting and Eliminating Hot Rolled Surface Defects

    Amount: $500,000.00

    The Small Business Technology Transfer Research (STTR) Phase II project will develop an inference engine for an intelligent imaging system that can detect and eliminate surface defects in hot rolling ...

    STTRPhase II2007National Science Foundation

Agency Micro-sites

US Flag An Official Website of the United States Government